• Reset SimpliSafe

How to Reset SimpliSafe Base Station?

  1. Detach the “SimpliSafe base station” from the power socket.
  2. Flip the “base station” upside down to reach the battery door.
  3. Open the “battery door” with a screwdriver and remove the batteries within the battery compartment.
  4. Hold on for about 30-45 seconds.
  5. Plug the base back into the “wall socket”.
  6. Now, “replace” the batteries removed from the base station.
  7. The Guidance for How to Reset SimpliSafe Base Station is Successfully Completed
how to reset simplisafe

How to Reset SimpliSafe Keypad?

  1. Unscrew the bottom of the base station.
  2. “Twist” the bottom to release it.
  3. Find the black button 180 degrees from the power cable slot.
  4. Press that button and any button on the keypad.
  5. The SimpliSafe keypad is now reset.

How to Reset SimpliSafe Base?

  1. Detach the SimpliSafe base station from the power socket.
  2. Flip the base station upside down to reach the battery door.
  3. Open the battery door with a screwdriver and remove the batteries within the battery compartment.
  4. Hold on for about 30-45 seconds.
  5. Plug the base back into the wall socket.
  6. Now, replace the batteries removed from the base station.

How to Factory Reset SimpliSafe Camera?

  1. Power on the camera.
  2. Press the Reset button on the camera for about “20 seconds”.
  3. The status light goes off and then flashes.
  4. Now, place the SimpliSafe Camera on top of the box.
  5. Keep your phone camera approximately 18 inches away from the camera lens.
  6. Make sure that the lens is at the center of the screen.
  7. Take your phone slowly near to the CAMERA.
  8. The phone is detected by the camera at about six inches away.

How to Factory Reset SimpliSafe Pin?

  1. Switch your alarm off.
  2. Remind yourself of the current Master PIN.
  3. Press the Menu button on your keypad.
  4. Key in the “current Master PIN” in the text field.
  5. The first option of the Menu panel is Change your PIN.
  6. “Select” the first option by pressing the blue Away button.
  7. “Input “your new PIN.
  8. Confirm the pin by re-entering it again.
  9. Press the Menu button again to exit.

How do I Reset my SimpliSafe Siren?

  1. Press the black button on the back side of the siren.
  2. Push the Off button on your keychain remote repeatedly while simultaneously holding down the black button.
  3. The Siren will emit a short tone after pressing the Off button thrice.

How do I Reset SimpliSafe Alarm

  1. Open the exit door.
  2. Put the status of the lock in the Home mode in the app.
  3. Now, exit the house and close the door.
  4. Another method is to exit and hit the Off button.
  5. Now, press the Away button while still pressing Off.
  6. The alarm is reset.

How do I Hard Reset SimpliSafe Doorbell?

  1. Remove the doorbell camera from the app.
  2. Unscrew the bottom of the doorbell and remove it from the base.
  3. Hold down the larger button behind the camera for a full minute.
  4. Release the button and wait for 30 seconds.
  5. Now, install the camera again following the instructions given above.
  6. Reconnect the camera to the base only when the bar code scanning step has to be done.

How to Factory Reset SimpliSafe system?

The SimpliSafe system can be reboot to default settings after an alarm or error.

  1. Remove the SimpliSafe base station from the power socket.
  2. Access the battery door by flipping the base station upside down.
  3. Unscrew the battery door and remove the batteries within the battery compartment.
  4. Hold on for about 30-45 seconds.
  5. Insert the base back into the wall socket.
  6. Now, replace the batteries removed from the base station.

How to factory Reset SimpliSafe?

Since each unit is programmed separately, there are no factory settings in SimpliSafe. Resetting the base station can bring back the default settings of the system. Learn How to Reset SimpliSafe using following Guidelines.

  1. Unplug the SimpliSafe base station from the power socket.
  2. Rotate the base station upside down to reach the battery door.
  3. Open the battery door and take away the batteries from within the compartment.
  4. Hold on for about 30-45 seconds.
  5. Plug the base back into the wall socket.
  6. Now, replace the batteries removed from the base station.
Installation Guide